The following section describes the I/O Sampling API Frames that apply to the XBee for Wi-SUN device.
Version
- Welcome to the Digi Wi-SUN solution
- Get started
- Learn how the solution works
- Architecture models
- XBee for Wi-SUN nodes
- XBee Hive for Wi-SUN Border Router
- Manage the network
- Develop applications
- Security
- Advanced topics
-
Reference material
-
API Frames
- User Data Relay
- Configuration
-
Communication
- TX Request Message - 0x1A
- Socket Create - 0x40
- Socket Option Request - 0x41
- Socket Connect - 0x42
- Socket Close - 0x43
- Socket Send (Transmit) - 0x44
- Socket Bind/Listen - 0x46
- Socket SendTo (Transmit Explicit Data) - 0x47
- Socket Create Response - 0xC0
- Connection Response - 0xC1
- Socket Close Response - 0xC2
- Socket Close Response - 0xC3
- Socket Listen Response - 0xC6
- Socket New IPv6 Client - 0xCA
- Socket Receive From - IPv6 - 0xCB
- Socket Receive - 0xCD
- Socket State - 0xCF
- Status
- I/O Sampling
- File System
-
AT commands
-
Networking
- AI (Association Indication)
- CE (Routing/Messaging Mode)
- DO (Device Options)
- IP (Transmission Protocol)
- JN (Join Network)
- LN (Leave Network)
- NI (Node Identifier)
- PB (Ping Payload Size)
- PG (Ping Command)
- PI (Ping Timeout)
- RN (Reset Network Credential Cache)
- WC (Channel Plan)
- WM (PHY Mode)
- WN (Network Name)
- WS (Network Size)
-
Addressing
- C0 (Source Port)
- DE (Destination Port)
- DL (Destination Address)
- MB (IPv6 Border Router Network Address)
- ML (IPv6 Link Local Network Address)
- MP (IPv6 Primary Parent Network Address)
- MS (IPv6 Global Secondary Parent Address)
- MY (IPv6 Global Network Address)
- SH (Serial Number High)
- SL (Serial Number Low)
- Security
- MicroPython
- File system
- API configuration
- AT command options
- UART interface
- UART pin configuration
- SMT/MMT SPI interface
-
I/O settings
- CB (Commissioning Pushbutton)
- D0 (DIO0/AD0/Commissioning Button Configuration)
- D1 (DIO1/AD1/TH_SPI_ATTN Configuration)
- D2 (DIO2/AD2/TH_SPI_CLK Configuration)
- D3 (DIO3/AD3/TH_SPI_SSEL Configuration)
- D4 (DIO4/TH_SPI_MOSI Configuration)
- D5 (DIO5/Associate Configuration)
- D8 (DIO8/DTR/SLP_Request Configuration)
- D9 (DIO9/ON_SLEEP Configuration)
- LT (Associate LED Blink Time)
- M0 (PWM0 Duty Cycle)
- M1 (PWM1 Duty Cycle)
- P0 (DIO10/RSSI/PWM0 Configuration)
- P1 (DIO11/PWM1 Configuration)
- P2 (DIO12/TH_SPI_MISO Configuration)
- PD (Pull Up/Down Direction)
- PR (Pull-Up/Down Resistor Enable)
- RP (RSSI PWM Timer)
- I/O sampling
- Location
- Diagnostic - FW/HW Information
- Memory access
- Custom default
- MAC/PHY
- OpenCSMP management
-
Networking
-
API Frames
- Troubleshooting
-
Hardware
- Border Router hardware
- XBee node hardware
- Design files
-
Safety instructions
- Safety instructions
- Инструкции за безопасност
- Sigurnosne upute
- Bezpečnostní instrukce
- Sikkerhedsinstruktioner
- Veiligheidsinstructies
- Ohutusjuhised
- Turvallisuusohjeet
- Consignes de sécurité
- Sicherheitshinweise
- Οδηγίες ασφαλείας
- Biztonsági utasítások
- Istruzioni di sicurezza
- Drošības instrukcijas
- Saugos instrukcijos
- Sikkerhetsinstruksjoner
- Instrukcje bezpieczeństwa
- Instruções de segurança
- Instructiuni de siguranta
- Bezpečnostné inštrukcie
- Varnostna navodila
- Instrucciones de seguridad
- Säkerhets instruktioner
I/O Sampling
