Review TX40 default settings

You can review the default settings for your TX40 device by using the local WebUI or Digi Remote Manager:

Local WebUI

  1. Log into the TX40 WebUI as a user with Admin access. See Using the local web interface for details.
  2. On the menu, click System > Device Configuration.

Digi Remote Manager

  1. If you have not already done so, connect to your Digi Remote Manager account.
  2. From the menu, click Devices to display a list of your devices.
  3. Locate your device as described in Use Digi Remote Manager to view and manage your device.
  4. Click the Device ID.
  5. Click Settings.
  6. Click to expand Config.

The following tables list important factory default settings for the TX40.

Default interface configuration

Interface type Preconfigured interfaces Devices Default configuration

Wide Area Network (WAN)

  • WAN
  • Ethernet: ETH1
  • Firewall zone: External
  • WAN priority: Metric=1
  • IP Address: DHCP client
  • Digi SureLinkTM enabled for IPv4
Wireless Wide-Area Networks (WWANs)
  • WWAN1
  • WWAN1 cellular modem
  • Firewall zone: External
  • WAN priority: Metric=3
  • SIM failover after 5 attempts
  • Digi SureLinkTM enabled for IPv4
Local Area Networks (LANs)
  • LAN
  • Bridge: LAN
  • Firewall zone: Internal
  • IP address: 192.168.2.1/24
  • DHCP server enabled
  • LAN priority: Metric=5
 
  • LAN hotspot
  • Bridge: hotspot_bridge
  • Firewall zone: Internal
  • DHCP server: disabled
 
  • Loopback
  • Ethernet: Loopback
  • Firewall zone: Loopback
  • IP address: 127.0.0.1/8
 
  • Setup IP
  • Bridge: LAN
  • Firewall zone: Setup
  • IP address 192.168.210.1/24
 
  • Setup Link-local IP
  • Bridge: LAN
  • Firewall zone: Setup
  • IP address 169.254.100.100/16
Wi-Fi
  • Wi-Fi access point: Digi AP (Wi-Fi1)
  • Wi-Fi1 radio: wifi1
  • Enabled
  • SSID: Digi-TX40-serial_number
  • Encryption: WPA2 Personal (PSK)
  • Pre-shared key: The unique password printed on the bottom label of the device.
 
  • Wi-Fi access point: Digi AP (Wi-Fi2)
  • Wi-Fi2 radio: wifi2
  • Enabled
  • SSID: Digi-TX40-serial_number
  • Encryption: WPA2 Personal (PSK)
  • Pre-shared key: The unique password printed on the bottom label of the device.
 
  • Hotspot access point: Digi Hotspot AP (Wi-Fi1)
  • Wi-Fi1 radio: wifi1
  • Disabled
  • SSID: Digi Hotspot
  • Encryption: Open (Unencrypted)
 
  • Hotspot access point: Digi Hotspot AP (Wi-Fi2)
  • Wi-Fi2 radio: wifi2
  • Disabled
  • SSID: Digi Hotspot
  • Encryption: Open (Unencrypted)
Bridges
  • Bridge: LAN
  • Ethernet: ETH2
  • Wi-Fi access point: Digi AP (Wi-Fi1)
  • Wi-Fi access point: Digi AP (Wi-Fi2)
  • Enabled
  • Used by the LAN interface
 
  • hotspot_bridge
  • Wi-Fi access point: Digi Hotspot AP (Wi-Fi1)
  • Wi-Fi access point: Digi Hotspot AP (Wi-Fi2)
  • Disabled
  • Used by the hotspot interface
Hotspot
  • hotspot
  • Bridge: hotspot_bridge
  • Disabled
  • Authentication mode: Click-through
  • IP address: 10.1.0.1/24
  • DHCP server: Automatically enabled (on all hotspots)
  • DHCP server lease range: 100-250

Other default configuration settings

Feature Configuration
Central management
  • Digi Remote Manager enabled as the central management service.
Security policies
  • Packet filtering allows all outbound traffic.
  • SSH and web administration:
    • Enabled for local administration
    • Firewall zone: Internal
Monitoring
  • Device heath metrics uploaded to Digi Remote Manager at 60 minute interval.
  • SNMP: Disabled
Serial port
  • Enabled
  • Serial mode: Login
  • Label: None
  • Baud rate:
  • Data bits: 8
  • Parity: None
  • Stop bits: 1
  • Flow control: None