ConnectPort X4 H LEDs

LED/button	Color and Light Pattern	Description
Power LED	Green	Power on.
Not illuminated	Power off.
Status LED	Yellow	Blinks during product initialization and factory reset, using the light patterns below. During normal device operation, after initialization, and factory reset, this LED is off and should never blink. If it blinks constantly, contact Digi Technical Support.
1-1-1 blinking yellow	Initializing firmware.
1-5-1 blinking yellow	Device configuration has been restored to its factory defaults.
Other blinking yellow	Contact Digi Technical Support.
Cellular Link LED	Solid yellow	Cellular link is up.
Cellular Activity LEDs	Blinking green	Cellular traffic is on the link.
Cellular Signal Strength LEDs	Amber or green depending on cellular signal type	Relative signal strength indicator (RSSI), shown as a number of LEDs. 0: signal strength unknown or unacceptable 1: signal strength low/weak 5:: signal strength high/excellent You can find specific dB values for the signal via the web interface; go to Administration > System Information > Mobile. Under Mobile Connection, the signal strength appears in bars and dBm. Or, from the command line, type the display mobile command. ConnectPort X4 models have a feature where the signal strength LEDs change colors to indicate which type of cellular signal is detected. Amber = 2G network Green = 3G network
XBee Link LED	Green	Indicates that the XBee RF module in the gateway has associated with an XBee network. For more information on the states indicated by this LED, see the description of the D5 (DIO5 Configuration) parameter in the product manual for the XBee RF module.
Solid green	XBee module in gateway is associated (or coordinator is started).
Fast blinking (20 Hz) green	An Ident (identify) button has been pressed on a remote node.
Slow (1 Hz) blinking green	XBee module in gateway is not associated.
Off	XBee module in gateway is disabled or not recognized.
XBee Activity LED	Yellow	On for 25 ms when data is sent or received from the XBee module in the gateway.
Ethernet Link LED	Solid yellow	Ethernet link is up.
Ethernet Activity LED	Blinking green	Ethernet traffic is on the link.
Reset button (ConnectPort X4 model only)	N/A	Single press: Performs equivalent of a power-cycle. Press and hold: Resets device configuration settings to factory defaults (factory reset). There is no reset button on the ConnectPort X4 H.

Power LED

Green

Power on.

Not illuminated

Power off.

Status LED

Yellow

Blinks during product initialization and factory reset, using the light patterns below. During normal device operation, after initialization, and factory reset, this LED is off and should never blink. If it blinks constantly, contact Digi Technical Support.

1-1-1 blinking yellow

Initializing firmware.

1-5-1 blinking yellow

Device configuration has been restored to its factory defaults.

Other blinking yellow

Contact Digi Technical Support.

Cellular Link LED

Solid yellow

Cellular link is up.

Cellular Activity LEDs

Blinking green

Cellular traffic is on the link.

Cellular Signal Strength LEDs

Amber or green depending on cellular signal type

Relative signal strength indicator (RSSI), shown as a number of LEDs.

0: signal strength unknown or unacceptable
1: signal strength low/weak
5:: signal strength high/excellent

You can find specific dB values for the signal via the web interface; go to Administration > System Information > Mobile. Under Mobile Connection, the signal strength appears in bars and dBm. Or, from the command line, type the display mobile command.

ConnectPort X4 models have a feature where the signal strength LEDs change colors to indicate which type of cellular signal is detected.

Amber = 2G network

Green = 3G network

XBee Link LED

Green

Indicates that the XBee RF module in the gateway has associated with an XBee network. For more information on the states indicated by this LED, see the description of the D5 (DIO5 Configuration) parameter in the product manual for the XBee RF module.

Solid green

XBee module in gateway is associated (or coordinator is started).

Fast blinking (20 Hz) green

An Ident (identify) button has been pressed on a remote node.

Slow (1 Hz) blinking green

XBee module in gateway is not associated.

Off

XBee module in gateway is disabled or not recognized.

XBee Activity LED

Yellow

On for 25 ms when data is sent or received from the XBee module in the gateway.

Ethernet Link LED

Solid yellow

Ethernet link is up.

Ethernet Activity LED

Blinking green

Ethernet traffic is on the link.

Reset button

(ConnectPort X4 model only)

N/A

Single press: Performs equivalent of a power-cycle.

Press and hold: Resets device configuration settings to factory defaults (factory reset).

There is no reset button on the ConnectPort X4 H.